-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 http://www.murty.net/ataraid/ <---very good documentation, used a lot from here. I think this is going to be your biggest help. I did the same thing, my / is on my ata 133 onboard raid card. my fstab looks like this: /dev/ataraid/d0p2 / auto defaults,noatime,nodiratime,notail 0 1 but i also had to add a kernel command line option. image=/vmlinuz label=Linux read-only # restricted # alias=1 append="ide3=0xd400,0xd002 ide4=0xb800,0xb402" - From /proc/pci RAID bus controller: Promise Technology, Inc. PDC20276 IDE (rev 1). IRQ 3. Master Capable. Latency=32. Min Gnt=4.Max Lat=18. I/O at 0xd400 [0xd407]. I/O at 0xd000 [0xd003]. I/O at 0xb800 [0xb807]. I/O at 0xb400 [0xb403]. I/O at 0xb000 [0xb00f]. Non-prefetchable 32 bit memory at 0xd5800000 [0xd5803fff]. Also, I compiled my own kernel, so I made sure I had all the ata raid drivers built into my kernel. linux:/etc# cat /proc/partitions major minor #blocks name rio rmerge rsect ruse wio wmerge wsect wuse running use aveq 114 0 78177280 ataraid/d0 0 0 0 0 0 0 0 0 0 0 0 114 1 1084356 ataraid/d0p1 0 0 0 0 0 0 0 0 0 0 0 114 2 77087902 ataraid/d0p2 0 0 0 0 0 0 0 0 0 0 0 56 0 39088896 hdi 42945 132017 1179302 4694420 67548 212687 1906609 1922080 -2 104919470 -203789680 34 0 39088896 hdg 42395 132152 1175694 3437250 66511 216957 1910983 1835150 -2 104864870 -205133720 34 1 1084356 hdg1 0 0 0 0 0 0 0 0 0 0 0 34 2 77087902 hdg2 0 0 0 0 0 0 0 0 0 0 0 22 0 2608160 hdc 0 0 0 0 0 0 0 0 -29 105140930 1285869526 3 0 39088896 hda 2 3 16 30 0 0 0 0 -2 105203110 -210406190 3 1 39078081 hda1 0 0 0 0 0 0 0 0 0 0 0 3 64 39088896 hdb 837 7098 62850 321890 56 24 640 60 -2 105203040 - -210084270 3 65 489951 hdb1 0 0 0 0 0 0 0 0 0 0 0 3 66 38596162 hdb2 835 7095 62834 321870 56 24 640 60 0 3050 321930 linux:/etc# df Filesystem 1K-blocks Used Available Use% Mounted on /dev/ataraid/d0p2 77085540 19997240 57088300 26% / On Tuesday 08 October 2002 21:10, Miles Beck wrote: > > 3 #cat /proc/partitions > > > > 4 see if you can see the partition that your new raid device is on > > (check sizes etc) > > I do not have the boot cd but by moving the master drive back to the > non-raid controller I was able to see the partitions file. Below is what > you asked for. At this point I have no idea what to do, ;) > > 114 0 117220792 ataraid/d0 > 114 1 248976 ataraid/d0p1 > 114 2 996030 ataraid/d0p2 > 114 3 2000092 ataraid/d0p3 > 114 4 1 ataraid/d0p4 > 114 5 248976 ataraid/d0p5 > 114 6 2000061 ataraid/d0p6 > 114 7 248976 ataraid/d0p7 > 114 8 248976 ataraid/d0p8 > 114 9 111225996 ataraid/d0p9 > 33 0 117220824 hde > 33 1 248976 hde1 > 33 2 996030 hde2 > 33 3 2000092 hde3 > 33 4 1 hde4 > 33 5 248976 hde5 > 33 6 2000061 hde6 > 33 7 248976 hde7 > 33 8 248976 hde8 > 33 9 111225996 hde9 > 3 0 117220824 hda > 3 1 248976 hda1 > 3 2 996030 hda2 > 3 3 2000092 hda3 > 3 4 1 hda4 > 3 5 248976 hda5 > 3 6 2000061 hda6 > 3 7 248976 hda7 > 3 8 248976 hda8 > 3 9 111225996 hda9 > > -=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us > To subscribe, unsubscribe, or to change you mail settings: > http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.0 (GNU/Linux) iD8DBQE9o7qkzFstip5OIqgRAm4kAJ9ZUBhF6PUN0EreKNG5gT9jKhFp4QCeL01r NA7jb6NFbU2hociBUBCjQcY= =HTvL -----END PGP SIGNATURE-----